Time-temperature Indicators Based on the Acidic Permanganate-oxalate Reaction System

193631-Thumbnail Image.png
Description
The kinetic behavior of acidified aqueous reaction systems based on the oxidation of sodium oxalate by potassium permanganate was investigated by UV-Vis absorbance spectrophotometry as part of a wider project to develop time-temperature indicators based on such systems. Reaction systems…

The kinetic behavior of acidified aqueous reaction systems based on the oxidation of sodium oxalate by potassium permanganate was investigated by UV-Vis absorbance spectrophotometry as part of a wider project to develop time-temperature indicators based on such systems. Reaction systems in various eutectic salt solutions as well as salt-free aqueous solutions were prepared and measured to establish the precision and accuracy of four different reaction systems designed to run for specified periods of time at 25°C. Reaction progress was also monitored in reaction systems previously subjected to prolonged periods of storage at −80°C, as well as systems subjected to repeated freezing and thawing, to determine the effect of preliminary freeze time or multiple freeze-thaw cycles on reaction run time. Eutectic-free aqueous reaction systems showed a noticeable decrease in run time from freshly frozen to 2 week frozen, but minimal to no decrease with increasing preliminary freeze time. Perchlorate-based reaction systems showed minimal to no decrease in reaction time with increasing preliminary freeze time, and were found to be capable of tolerating up to three <5-minute excursions into room temperature before reaction time was significantly affected. It was also found that all reaction systems studied were capable of reaching their target run times within the intended ±10% limit of accuracy, as average run times for each system ranged from 0.4% to 6.9% off from the target run time. These systems were found to be reproducible with considerable precision as well, with the average coefficient of variation for each system ranging from 2.6 to 5.5.
Date Created
2024
Agent

Investigating the Effect of Atmospheric Ozone on Ragweed Pollen

193580-Thumbnail Image.png
Description
Pollen allergies are common in the United States, especially in Arizona. In addition to more people experiencing allergies, the allergies themselves are worse, with people reporting more severe and longer lasting symptoms, after moving to Arizona. Potential reasons behind this…

Pollen allergies are common in the United States, especially in Arizona. In addition to more people experiencing allergies, the allergies themselves are worse, with people reporting more severe and longer lasting symptoms, after moving to Arizona. Potential reasons behind this include a longer blooming season in the state, a lack of rain to wash out pollen from the atmosphere, and compounding factors of poor air quality. One significant contributor to poor air quality are high ozone levels in urban areas like Phoenix. The goal of this study is to determine if ozone and pollen interact in a way that changes pollen physically or chemically. Ragweed pollen was placed in a chamber and exposed to low, medium, and high levels of ozone for 6-72 hours corresponding to different exposure doses. Exposed and non-exposed pollen was analyzed for physical changes in the pollen grain using scanning electron microscopy (SEM). Chemical changes were investigated using Fourier Transform Infrared Spectroscopy (FT-IR). Finally, exposed and non-exposed pollen was analyzed for changes in lipid profiles using gas chromatography mass spectrometry (GC/MS). SEM analysis found that when ragweed pollen is exposed to high ozone levels (60-100 ppm, > 48 hours), pollen grains become damaged. The same exposure level results in chemical changes in the pollen that are detectable by FT-IR. A higher ozone dose results in worse physical damage and increased changes in the lipid profile. Future research should study a wider ranges of exposure doses and relate the physicochemical changes to differences in immune response.
Date Created
2024
Agent

Polycyclic Aromatic Hydrocarbons and Particulate Matter in Tempe Arizona

193481-Thumbnail Image.png
Description
ABSTRACT Tempe, Arizona can experience high atmospheric particulate matter episodes, both in winter and in summer. In summer, such events might be due to dust storms or wildfires, while in the wintertime, domestic wood burning (fireplaces and heating)…

ABSTRACT Tempe, Arizona can experience high atmospheric particulate matter episodes, both in winter and in summer. In summer, such events might be due to dust storms or wildfires, while in the wintertime, domestic wood burning (fireplaces and heating) tends to be a major contributor. In this study, it was investigated that the particulate matter concentrations and composition for select summertime and wintertime events in Tempe, expected to have high concentrations and possibly biomass burning impacts. Summertime concentrations on the selected days were low except for a dust storm event. In the winter events, across the New Year holiday, concentrations were substantial, especially on New Year's morning because of the fireworks, although precipitation impacted the concentrations. Chemical analysis of bulk organic (OC) and elemental (EC) carbon shows a high ratio of OC/EC, indicative of substantial secondary organic aerosol contributions or biomass burning. Investigation of biomass burning specific molecular markers, such as levoglucosan, using gas chromatography mass spectrometry, showed detectable concentrations during wintertime, confirming wood burning as a significant source of atmospheric particulate matter. In summer, levoglucosan was detected but during the times investigated, wood smoke was not a dominant source of particulate matter. Finally, particulate polycyclic aromatic hydrocarbons (PAH) of burning origin were also investigated because of their toxicity. PAH concentrations showed a clear dependence of temperature with lower molecular weighted (LMW) PAHs being less abundant in the summertime in the particulate matter because of their volatility. The use of diagnostic PAH ratios confirmed the importance of combustion sources for the PAH albeit different ones in summer compared to winter events.
Date Created
2024
Agent

Microplastics in the Desert Southwest: Occurrence and Characterization In Atmospheric, Aquatic, and Terrestrial Environments

193034-Thumbnail Image.png
Description
Microplastics, plastics smaller than 5 mm, are an emerging concern worldwide due to their potential adverse effects on the environment and human health. Microplastics have the potential to biomagnify through the food chain, and are prone to adsorbing organic pollutants…

Microplastics, plastics smaller than 5 mm, are an emerging concern worldwide due to their potential adverse effects on the environment and human health. Microplastics have the potential to biomagnify through the food chain, and are prone to adsorbing organic pollutants and heavy metals. Therefore, there is an urgent need to assess the extent of microplastic contamination in different environments. The occurrence of microplastics in the atmosphere of Tempe, AZ was investigated and results show concentrations as high as 1.1 microplastics/m3. The most abundant identified polymer was polyvinyl chloride. However, chemical characterization is fraught with challenges, with a majority of microplastics remaining chemically unidentified. Laboratory experiments simulating weathering of microplastics revealed that Raman spectra of microplastics change over time due to weathering processes. This work also studied the spatial variation of microplastics in soil in Phoenix and the surrounding areas of the Sonoran Desert, and microplastic abundances ranged from 122 to 1299 microplastics/kg with no clear trends between different locations, and substantial total deposition of microplastics occurring in the same location with resuspension and redistribution of deposited microplastics likely contributing to unclear spatial trends. Temporal variation of soil microplastics from 2005 to 2015 show a systematic increase in the abundance of microplastics. Polyethylene was prominent in all soil samples. Further, recreational surface waters were investigated as a potential source of microplastics in aquatic environments. The temporal variation of microplastics in the Salt River, AZ over the course of one day depicted an increase of 8 times in microplastic concentration at peak activity time of 16:00 hr compared to 8:00 hr. Concurrently, microplastic concentrations in surface water samples from apartment community swimming pools in Tempe, AZ depicted substantial variability with concentrations as high as 254,574 MPs/m3. Polyester and Polyamide fibers were prevalent in surface water samples, indicating a release from synthetic fabrics. Finally, a method for distinguishing tire wear microplastics from soot in ambient aerosol samples was developed using Programmed Thermal Analysis, that allows for the quantification of Elemental Carbon. The method was successfully applied on urban aerosol samples with results depicting substantial fractions of tire wear in urban atmospheric environments.
Date Created
2024
Agent

Assessing Exposure and Evaluating the Efficiency of Filters and Masks in Capturing Airborne Nanoparticles

189350-Thumbnail Image.png
Description
The prevalence and unique properties of airborne nanoparticles have raised concerns regarding their potential adverse health effects. Despite their significance, the understanding of nanoparticle generation, transport, and exposure remains incomplete. This study first aimed to assess nanoparticle exposure in indoor…

The prevalence and unique properties of airborne nanoparticles have raised concerns regarding their potential adverse health effects. Despite their significance, the understanding of nanoparticle generation, transport, and exposure remains incomplete. This study first aimed to assess nanoparticle exposure in indoor workplace environments, in the semiconductor manufacturing industry. On-site observations during tool preventive maintenance revealed a significant release of particles smaller than 30 nm, which subsequent instrumental analysis confirmed as predominantly composed of transition metals. Although the measured mass concentration levels did not exceed current federal limits, it prompted concerns regarding how well filter-based air sampling methods would capture the particles for exposure assessment and how well common personal protective equipment would protect from exposure. To address these concerns, this study evaluated the capture efficiency of filters and masks. When challenged by aerosolized engineered nanomaterials, common filters used in industrial hygiene sampling exhibited capture efficiencies of over 60%. Filtering Facepiece Respirators, such as the N95 mask, exhibited a capture efficiency of over 98%. In contrast, simple surgical masks showed a capture efficiency of approximately 70%. The experiments showed that face velocity and ambient humidity influence capture performance and mostly identified the critical role of mask and particle surface charge in capturing nanoparticles. Masks with higher surface potential exhibited higher capture efficiency towards nanoparticles. Eliminating their surface charge resulted in a significantly diminished capture efficiency, up to 43%. Finally, this study characterized outdoor nanoparticle concentrations in the Phoenix metropolitan area, revealing typical concentrations on the order of 10^4 #/cm3 consistent with other urban environments. During the North American monsoon season, in dust storms, with elevated number concentrations of large particles, particularly in the size range of 1-10 μm, the number concentration of nanoparticles in the size range of 30-100 nm was substantially lower by approximately 55%. These findings provide valuable insights for future assessments of nanoparticle exposure risks and filter capture mechanisms associated with airborne nanoparticles.
Date Created
2023
Agent

Community Air Quality Measurement, Management, and Control Methods

189340-Thumbnail Image.png
Description
As air quality standards become more stringent to combat poor air quality, there is a greater need for more effective pollutant control measures and increased air monitoring network coverage. Polluted air, in the form of aerosols and gases, can impact…

As air quality standards become more stringent to combat poor air quality, there is a greater need for more effective pollutant control measures and increased air monitoring network coverage. Polluted air, in the form of aerosols and gases, can impact respiratory and cardiovascular health, visibility, the climate, and material weathering. This work demonstrates how traditional networks can be used to study generational events, how these networks can be supplemented with low-cost sensors, and the effectiveness of several control measures. First, an existing network was used to study the effect of COVID-19 travel restrictions on air quality in Maricopa County, Arizona, which would not have been possible without the historical record that a traditional network provides. Although this study determined that decreases in CO and NO2 were not unique to the travel restrictions, it was limited to only three locations due to network sparseness. The second part of this work expanded the traditional NO2 monitoring network using low-cost sensors, that were first collocated with a reference monitor to evaluate their performance and establish a robust calibration. The sensors were then deployed to the field to varying results; their calibration was further improved by cycling the sensors between deployment and reference locations throughout the summer. This calibrated NO2 data, along with volatile organic compound data, were combined to enhance the understanding of ozone formation in Maricopa County, especially during wildfire season. In addition to being in non-attainment for ozone standards, Maricopa County fails to meet particulate matter under 10 μm (PM10) standards. A large portion of PM10 emissions is attributed to fugitive dust that is either windblown or kicked up by vehicles. The third part of this work demonstrated that Enzyme Induced Carbonate Precipitation (EICP) treatments aggregate soil particles and prevent fugitive dust emissions. The final part of the work examined tire wear PM10 emissions, as vehicles are another significant contributor to PM10. Observations showed a decrease in tire wear PM10 during winter with little change when varying the highway surface type.
Date Created
2023
Agent

Analysis of Retroreflective Glass Beads in Soil Samples for Forensic Investigations

187871-Thumbnail Image.png
Description
Trace evidence is an essential component of forensic investigations. Anthropogenicmaterials such as fibers and glass have been well studied for use in forensic trace evidence, but the potential use of retroreflective beads found in soils for forensic investigations is largely…

Trace evidence is an essential component of forensic investigations. Anthropogenicmaterials such as fibers and glass have been well studied for use in forensic trace evidence, but the potential use of retroreflective beads found in soils for forensic investigations is largely unexplored. Retroreflective glass beads are tiny spheres mixed into pavement markings to create reflective surfaces to reduce lane departure accidents. Retroreflective glass beads are a potentially new source of trace evidence for forensic investigations. Analysis of the spatial distribution and chemical compositions of retroreflective glass beads recovered from 17 soil samples were analyzed and compared to see if there are striking variations that can distinguish samples by source. Soil samples taken near marked roads showed significantly higher concentrations of glass beads, averaging from 0.18 bead/g of soil sample to 587 beads/g of soil, while soil samples taken near unmarked roads had average range of concentration of 0 bead/g of soil to 0.21 bead/g of soil. Retroreflective glass beads come from pavement markings, thus soil samples near marked roads are expected to have higher concentrations of glass beads. Analysis of spatial distribution of glass beads showed that as sample collection moved further from the road, concentration of glass beads decreased. ICP-MS results of elemental concentrations for each sample showed discriminative differences between samples, for most of the elements. An analysis of variance for elemental concentrations was conducted, and results showed statistically significant differences, beyond random chance alone for half of the elements analyzed. For forensic comparisons, a significant difference in even just one element is enough to conclude that the samples came from different sources. The elemental concentrations of glass beads collected from the same location, but of varying differences, was also analyzed. ANOVA results show significant differences for only one or two elements. A pair-wise t-test was conducted to determine which elements are most discriminative among all the samples. Rubidium was found to be the most discriminative, showing significant difference for 67% of the pairs. Beryllium, potassium, and manganese were also highly discriminative, showing significant difference for at least 50% of all the pairs.
Date Created
2023
Agent

The Fate of Microplastics in Tres Rios, a Constructed Treatment Wetland

187393-Thumbnail Image.png
Description
Plastics are an emerging issue in aquatic ecosystems due to their slow degradation and ability to fragment into smaller more mobile parts. Concluding this process, plastics <5mm are categorized as Microplastics, MPs. Currently, the majority of MP studies bring attention…

Plastics are an emerging issue in aquatic ecosystems due to their slow degradation and ability to fragment into smaller more mobile parts. Concluding this process, plastics <5mm are categorized as Microplastics, MPs. Currently, the majority of MP studies bring attention to marine pollution and the impacts that follow. However, it remains a high priority to understand how MPs move through urban aquatic environments, and the impacts this may have for surrounding urban ecosystems. Little is known about how MPs move through tertiary treated wastewater plants, such as constructed wetlands, and how much, if any, remain trapped in abiotic and biotic material such as soil or plant life, respectively. An analysis of MP distribution using Tres Rios, a tertiary wastewater treatment wetland, as the study site may help to shed light on the source-occurrences of MPs. Microplastics extraction was performed on soil, plant, and water samples that were collected along major access points within the system with emphasis on inflow and outflow. The inflow of the wetland receives between 246-398 MPs/L vs the outflow of 90-199 MPs/L. Tres Rios soil concentrations ranged between 1,017-10,100 per kg and 133-700 MPs per kg in sampled vegetation throughout the wetland. The distribution of soil and vegetation samples differed throughout Tres Rios, as soil sampled exhibited higher quantities towards inflow site and vegetation MP occurrences were increased throughout the middle of the system. Additionally, this study aimed to determine if seasonality impacted the concentration of plastics seen throughout the system. There was no evidence that suggested seasonal variations were occurring in any sample type. Atmospheric deposition fluxes of microplastics were considered as a potential additional influx but even at the measured 1510 MP m-2 day-1 they were small compared to the water influx. Overall, the results suggest that the Tres Rios wetland removed 55% of the microplastics it receives and hence performs a substantial ecosystem service.
Date Created
2023
Agent

Iodine and Bromine Occurrence and Speciation in Atmospheric Particulate Matter

Description

Quantifying halogen presence and speciation in particulate matter is crucial given the role atmospheric particulates play in transport and cycling. While some halogens (fluorine and chlorine) are often included in aerosol studies, iodine and bromine have rarely been examined, especially…

Quantifying halogen presence and speciation in particulate matter is crucial given the role atmospheric particulates play in transport and cycling. While some halogens (fluorine and chlorine) are often included in aerosol studies, iodine and bromine have rarely been examined, especially outside of a marine environment. Focus on this environment is, in part, due to the existence of biogenic marine sources for both halogens. However, examining iodine and bromine in an urban environment has the potential to provide key insights into the transport and processing of these species in the atmosphere. As Tempe is set within a desert environment, bromine concentration is expected to be relatively high due to its presence in Earth’s crust, while iodine is expected to exist in higher concentrations near the coast. To detect presence and concentration, ICP-MS analysis was performed on samples taken in Tempe, AZ as well as sites in Bakersfield, CA and Davis, CA, which yielded preliminary results in line with these expectations. A secondary set of samples were taken in Tempe, AZ during dust storms, haboobs, and winter holidays. CIC was used to determine the organic fraction. In doing so, this study aims to identify species present in an urban environment as well as potential transportation pathways.

Date Created
2023-05
Agent

Transition Metal Catalyzed Depolymerization of Polyethylene Terephthalate and Synthesis of a Novel Redox-Active Ligand

Description

Post-consumer plastic and polymer waste accumulation in recent years continues to become more of a problem. One of the common polymers that has become ubiquitous to modern life is polyethylene terephthalate, a polymer that makes up 6.2% of all polymers…

Post-consumer plastic and polymer waste accumulation in recent years continues to become more of a problem. One of the common polymers that has become ubiquitous to modern life is polyethylene terephthalate, a polymer that makes up 6.2% of all polymers produced and only 39% of which is recycled in the US annually.1,5 In this study a new catalyst was for the methanolysis of PET and compared to a common organic base, 1,5,7-triazabicyclo[4.4.0]dec-5-ene (TBD), that has been used in academia and industry for the depolymerization of PET. In this study it was concluded that yttrium (III) acetylacetonate hydrate was a more active catalyst for the methanolysis of PET at 120 °C in comparison to TBD. It was also determined that there is no co-catalytic effect between yttrium (III) acetylacetonate hydrate and TBD when used in combination. The use of manganese (II) acetate tetrahydrate was also explored as a potential catalyst and was found to shown significant reactivity. However, it was concluded that the optimal conditions for PET methanolysis had not been reached and that further research into reaction times as well as co-solvents needs to be conducted. The synthesis of a novel o-phenylenediamine ligand functionalized with a labile phosphine substituent was also explored with the end goal of metalation and implementation in the methanolysis of PET. It has been assumed through nuclear magnetic resonance spectroscopy (NMR) characterization that the N,N’-(1,2-phenylenediamine)bis[3-(diphenylphosphanyl)-propanamide]-borane precursor was successfully synthesized and isolated. The subsequent deprotection of the N,N’-(1,2-phenylenediamine)bis[3-(diphenylphosphanyl)-propanamide]-borane complex was performed but has not been fully characterized. The 31P NMR does indicate a fully deprotected tertiary organophosphine. Through this work a detailed procedure for the ligand precursor has been laid out and developed so that the synthesis may now be scaled up, further characterized, metalated, and used to support catalysis.

Date Created
2023-05
Agent
Subscribe to Herckes, Pierre