Mitigation of Wide Angle Signal Interference in Terahertz Imaging Systems

156292-Thumbnail Image.png
Description
The objective of this work is to design a low-profile compact Terahertz (THz) imaging system that can be installed in portable devices, unmanned aerial vehicles (UAVs), or CubeSats. Taking advantage of the rotational motion of these platforms, one can use

The objective of this work is to design a low-profile compact Terahertz (THz) imaging system that can be installed in portable devices, unmanned aerial vehicles (UAVs), or CubeSats. Taking advantage of the rotational motion of these platforms, one can use linear antennas, such as leaky-wave antennas or linear phased arrays, to achieve fast image acquisition using simple RF front-end topologies. The proposed system relies on a novel image reconstructing technique that uses the principles of computerized tomography (Fourier-slice theorem). It can be implemented using a rotating antenna that produces a highly astigmatic fan-beam. In this work, the imaging system is composed of a linear phased antenna array with a highly directive beam pattern in the E-plane allowing for high spatial resolution imaging. However, the pattern is almost omnidirectional in the H-plane and extends beyond the required field-of-view (FOV). This is a major drawback as the scattered signals from any interferer outside the FOV will still be received by the imaging aperture and cause distortion in the reconstructed image. Also, fan beams exhibit significant distortion (curvature) when tilted at large angles, thus introducing errors in the final image due to its failure to achieve the assumed reconstructing algorithm.

Therefore, a new design is proposed to alleviate these disadvantages. A 14×64 elements non-uniform array with an optimal flat-top pattern is designed with an iterative process using linear perturbation of a close starting pattern until the desired pattern is acquired. The principal advantage of this design is that it restricts the radiated/received power into the required FOV. As a result, a significant enhancement in the quality of images is achieved especially in the mitigation of the effect of any interferer outside the FOV. In this report, these two designs are presented and compared in terms of their imaging efficiency along with a series of numerical results verifying the proof of concept.
Date Created
2018
Agent

Skin tissue terahertz imaging for fingerprint biometrics

155742-Thumbnail Image.png
Description
Fingerprints have been widely used as a practical method of biometrics authentication or identification with a significant level of security. However, several spoofing methods have been used in the last few years to bypass fingerprint scanners, thus compromising data security.

Fingerprints have been widely used as a practical method of biometrics authentication or identification with a significant level of security. However, several spoofing methods have been used in the last few years to bypass fingerprint scanners, thus compromising data security. The most common attacks occur by the use of fake fingerprint during image capturing. Imposters can build a fake fingerprint from a latent fingerprint left on items such as glasses, doorknobs, glossy paper, etc. Current mobile fingerprint scanning technology is incapable of differentiating real from artificial fingers made from gelatin molds and other materials. In this work, the adequacy of terahertz imaging was studied as an alternative fingerprint scanning technique that will enhance biometrics security by identifying superficial skin traits. Terahertz waves (0.1 – 10 THz) are a non-ionizing radiation with significant penetration depth in several non-metallic materials. Several finger skin features, such as valley depth and sweat ducts, can possibly be imaged by employing the necessary imaging topology. As such, two imaging approaches 1) using quasi-optical components and 2) using near-field probing were investigated. The numerical study is accomplished using a commercial Finite Element Method tool (ANSYS, HFSS) and several laboratory experiments are conducted to evaluate the imaging performance of the topologies. The study has shown that terahertz waves can provide high spatial resolution images of the skin undulations (valleys and ridges) and under certain conditions identify the sweat duct pattern.
Date Created
2017
Agent

Holographic Metasurface Leaky Wave Antennas

155235-Thumbnail Image.png
Description
Articially engineered two-dimensional materials, which are widely known as

metasurfaces, are employed as ground planes in various antenna applications. Due to

their nature to exhibit desirable electromagnetic behavior, they are also used to design

waveguiding structures, absorbers, frequency selective surfaces, angular-independent

surfaces, etc. Metasurfaces

Articially engineered two-dimensional materials, which are widely known as

metasurfaces, are employed as ground planes in various antenna applications. Due to

their nature to exhibit desirable electromagnetic behavior, they are also used to design

waveguiding structures, absorbers, frequency selective surfaces, angular-independent

surfaces, etc. Metasurfaces usually consist of electrically small conductive planar

patches arranged in a periodic array on a dielectric covered ground plane. Holographic

Articial Impedance Surfaces (HAISs) are one such metasurfaces that are capable of

forming a pencil beam in a desired direction, when excited with surface waves. HAISs

are inhomogeneous surfaces that are designed by modulating its surface impedance.

This surface impedance modulation creates a periodical discontinuity that enables a

part of the surface waves to leak out into the free space leading to far-eld radia-

tion. The surface impedance modulation is based on the holographic principle. This

dissertation is concentrated on designing HAISs with

Desired polarization for the pencil beam

Enhanced bandwidth

Frequency scanning

Conformity to curved surfaces

HAIS designs considered in this work include both one and two dimensional mod-

ulations. All the designs and analyses are supported by mathematical models and

HFSS simulations.
Date Created
2017
Agent

Applications of kinetic inductance: parametric amplifier & phase shifter, 2DEG coupled co-planar structures & microstrip to slotline transition at RF frequencies

154586-Thumbnail Image.png
Description
Kinetic inductance springs from the inertia of charged mobile carriers in alternating electric fields and it is fundamentally different from the magnetic inductance which is only a geometry dependent property. The magnetic inductance is proportional to the volume occupied by

Kinetic inductance springs from the inertia of charged mobile carriers in alternating electric fields and it is fundamentally different from the magnetic inductance which is only a geometry dependent property. The magnetic inductance is proportional to the volume occupied by the electric and magnetic fields and is often limited by the number of turns of the coil. Kinetic inductance on the other hand is inversely proportional to the density of electrons or holes that exert inertia, the unit mass of the charge carriers and the momentum relaxation time of these charge carriers, all of which can be varied merely by modifying the material properties. Highly sensitive and broadband signal amplifiers often broaden the field of study in astrophysics. Quantum-noise limited travelling wave kinetic inductance parametric amplifiers offer a noise figure of around 0.5 K ± 0.3 K as compared to 20 K in HEMT signal amplifiers and can be designed to operate to cover the entire W-band (75 GHz – 115 GHz).The research cumulating to this thesis involves applying and exploiting kinetic inductance properties in designing a W-band orthogonal mode transducer, quadratic gain phase shifter with a gain of ~49 dB over a meter of microstrip transmission line. The phase shifter will help in measuring the maximum amount of phase shift ∆ϕ_max (I) that can be obtained from half a meter transmission line which helps in predicting the gain of a travelling wave parametric amplifier. In another project, a microstrip to slot line transition is designed and optimized to operate at 150 GHz and 220 GHz frequencies, that is used as a part of horn antenna coupled microwave kinetic inductance detector proposed to operate from 138 GHz to 250 GHz. In the final project, kinetic inductance in a 2D electron gas (2DEG) is explored by design, simulation, fabrication and experimentation. A transmission line model of a 2DEG proposed by Burke (1999), is simulated and verified experimentally by fabricating a capacitvely coupled 2DEG mesa structure. Low temperature experiments were done at 77 K and 10 K with photo-doping the 2DEG. A circuit model of a 2DEG coupled co-planar waveguide model is also proposed and simulated.
Date Created
2016
Agent

Fast numerical algorithms for 3-D scattering from PEC and dielectric random rough surfaces in microwave remote sensing

154371-Thumbnail Image.png
Description
We present fast and robust numerical algorithms for 3-D scattering from perfectly electrical conducting (PEC) and dielectric random rough surfaces in microwave remote sensing. The Coifman wavelets or Coiflets are employed to implement Galerkin’s procedure in the method of moments

We present fast and robust numerical algorithms for 3-D scattering from perfectly electrical conducting (PEC) and dielectric random rough surfaces in microwave remote sensing. The Coifman wavelets or Coiflets are employed to implement Galerkin’s procedure in the method of moments (MoM). Due to the high-precision one-point quadrature, the Coiflets yield fast evaluations of the most off-diagonal entries, reducing the matrix fill effort from O(N^2) to O(N). The orthogonality and Riesz basis of the Coiflets generate well conditioned impedance matrix, with rapid convergence for the conjugate gradient solver. The resulting impedance matrix is further sparsified by the matrix-formed standard fast wavelet transform (SFWT). By properly selecting multiresolution levels of the total transformation matrix, the solution precision can be enhanced while matrix sparsity and memory consumption have not been noticeably sacrificed. The unified fast scattering algorithm for dielectric random rough surfaces can asymptotically reduce to the PEC case when the loss tangent grows extremely large. Numerical results demonstrate that the reduced PEC model does not suffer from ill-posed problems. Compared with previous publications and laboratory measurements, good agreement is observed.
Date Created
2016
Agent

Bluetooth low energy for use with MEM sensors

Description
ABSTRACT

Designers creating the next generation remote sensing enabled smart devices need to overcome the challenges of prevailing ventures including time to market and expense.

To reduce the time and effort involved in initial prototyping, a good reference design is often desired

ABSTRACT

Designers creating the next generation remote sensing enabled smart devices need to overcome the challenges of prevailing ventures including time to market and expense.

To reduce the time and effort involved in initial prototyping, a good reference design is often desired and warranted. This paper provides the necessary reference materials for Designers to implement a wireless solution efficiently and effectively.

This document is intended for users with limited Bluetooth technology experience.

Many sensing-enabled devices require a ‘hard-wire’ or cable link to a host monitoring system. This can limit the potential for product advancements by anchoring the system to a single location preventing portability and the convenience of a remote system. By removing the “wired” or cabled portion from a design, a broader scope of devices becomes feasible.

One common problematic area for these types of sensors is within the internal medicine field. Proximity sensing is far more practical and less invasive to implement than surgical implantation. Bluetooth Low Energy (BLE) systems solve the hard wired problem by decoupling the physical sensor from the host system through a BLE transceiver that can send information to an external monitoring system. This wireless link enables new sensor technology to be leveraged into previously unobtainable markets; such as, internal medicine, wearable devices, and Infotainment to name a few. Wireless technology for sensor systems are a potentially disruptive technology changing the way environmental monitoring is implemented and considered.

With this BLE design reference, products can be created with new capabilities to advance current technologies for military, commercial, industrial and medical sectors in rapid succession.
Date Created
2015
Agent

Wireless power transfer

153434-Thumbnail Image.png
Description
A new loop configuration capable of reducing power radiation magnitudes lower than conventional loops has been developed. This configuration is demonstrated for the case of two coaxial loops of 0.1 meter radius coupled via the magnetic reactive field. Utilizing electromagnetism

A new loop configuration capable of reducing power radiation magnitudes lower than conventional loops has been developed. This configuration is demonstrated for the case of two coaxial loops of 0.1 meter radius coupled via the magnetic reactive field. Utilizing electromagnetism theory, techniques from antenna design and a new near field design initiative, the ability to design a magnetic field has been investigated by using a full wave simulation tool. The method for realization is initiated from first order physics model, ADS and onto a full wave situation tool for the case of a non-radiating helical loop. The exploration into the design of a magnetic near field while mitigating radiation power is demonstrated using an real number of twists to form a helical wire loop while biasing the integer twisted loop in a non-conventional moebius termination. The helix loop setup as a moebius loop convention can also be expressed as a shorted antenna scheme. The 0.1 meter radius helix antenna is biased with a 1MHz frequency that categorized the antenna loop as electrically small. It is then demonstrated that helical configuration reduces the electric field and mitigates power radiation into the far field. In order to compare the radiated power reduction performance of the helical loop a shielded loop is used as a baseline for comparison. The shielded loop system of the same geometric size and frequency is shown to have power radiation expressed as -46.1 dBm. The power radiated mitigation method of the helix loop reduces the power radiated from the two loop system down to -98.72 dBm.
Date Created
2015
Agent

A novel ortho-mode transducer for the 750-1150 GHz band

153247-Thumbnail Image.png
Description
The design, fabrication and testing of a novel full waveguide band ortho-mode transducer (OMT) for operation from 750-1150 GHz is presented in this dissertation. OMT is a device that separates orthogonal polarizations within the same frequency band. At millimeter and

The design, fabrication and testing of a novel full waveguide band ortho-mode transducer (OMT) for operation from 750-1150 GHz is presented in this dissertation. OMT is a device that separates orthogonal polarizations within the same frequency band. At millimeter and sub millimeter wavelengths, OMTs can achieve precise characterization of the amplitude, spectrum and polarization of electromagnetic radiation by increasing spectral coverage and sensitivity while reducing aperture size, optical spill and instrumental polarization offsets. A fully planar design is implemented with the use of Robinson OMT model along with a planar finline circuit. CST Microwave Studio is used to design and simulate OMT. Existing finline circuits which were fabricated using photolithographic techniques on a thin dielectric substrate were employed. The finline chips are fabricated on a thin (1 µm) SOI substrate with thick (5 µm) gold finline metallization and gold beam leads for chip grounding. The OMT is designed with H plane splits in the through arm and E plane splits in the side arm to comply with the existing machining tools and technique. Computer Numerical Controlled (CNC) machining is used to fabricate the OMT split block. The OMT is tested at Jet Propulsion Laboratory (JPL) using Agilent PNA-X VNA and VDI WR1.0 extension heads. In the future, this OMT design could be a part of a fully integrated dual polarization mixer block, with the input horn, OMT and both mixers fabricated in a single flangeless split block. In Radio Astronomy, integrated dual polarization mixers of this type will increase the signal processing speed by 40%. This type of OMT can also be used for terahertz RADAR and communication purposes.
Date Created
2014
Agent

Magneto-dielectric wire antennas theory and design

152106-Thumbnail Image.png
Description
There is a pervasive need in the defense industry for conformal, low-profile, efficient and broadband (HF-UHF) antennas. Broadband capabilities enable shared aperture multi-function radiators, while conformal antenna profiles minimize physical damage in army applications, reduce drag and weight penalties in

There is a pervasive need in the defense industry for conformal, low-profile, efficient and broadband (HF-UHF) antennas. Broadband capabilities enable shared aperture multi-function radiators, while conformal antenna profiles minimize physical damage in army applications, reduce drag and weight penalties in airborne applications and reduce the visual and RF signatures of the communication node. This dissertation is concerned with a new class of antennas called Magneto-Dielectric wire antennas (MDWA) that provide an ideal solution to this ever-present and growing need. Magneto-dielectric structures (μr>1;εr>1) can partially guide electromagnetic waves and radiate them by leaking off the structure or by scattering from any discontinuities, much like a metal antenna of the same shape. They are attractive alternatives to conventional whip and blade antennas because they can be placed conformal to a metallic ground plane without any performance penalty. A two pronged approach is taken to analyze MDWAs. In the first, antenna circuit models are derived for the prototypical dipole and loop elements that include the effects of realistic dispersive magneto-dielectric materials of construction. A material selection law results, showing that: (a) The maximum attainable efficiency is determined by a single magnetic material parameter that we term the hesitivity: Closely related to Snoek's product, it measures the maximum magnetic conductivity of the material. (b) The maximum bandwidth is obtained by placing the highest amount of μ" loss in the frequency range of operation. As a result, high radiation efficiency antennas can be obtained not only from the conventional low loss (low μ") materials but also with highly lossy materials (tan(δm)>>1). The second approach used to analyze MDWAs is through solving the Green function problem of the infinite magneto-dielectric cylinder fed by a current loop. This solution sheds light on the leaky and guided waves supported by the magneto-dielectric structure and leads to useful design rules connecting the permeability of the material to the cross sectional area of the antenna in relation to the desired frequency of operation. The Green function problem of the permeable prolate spheroidal antenna is also solved as a good approximation to a finite cylinder.
Date Created
2013
Agent