-Please adjust the format of the abstract. m-3 should be typed as "m to the minus 3" with the "minus 3" in superscript
-see the additional "abstract.pdf" document for formatting
In arid environments like Phoenix, many professional and residential outdoor spaces are cooled by the use of misting systems. These systems spray a fine mist of water droplets that cool down the surrounding air through the endothermic evaporation process. When the water droplets evaporate, they leave behind dissolved material that is present in the water, generating ambient particulate matter (PM). Thus, misting systems are a point source of PM. Currently there is no information on their impact on air quality in close proximity to these systems, or on the chemical composition of the particulate matter generated by the evaporating mist.
In this project, PM concentrations are found to increase on average by a factor of 8 from ambient levels in the vicinity of a residential misting system in controlled experiments. PM concentrations in public places that use misting systems are also investigated. The PM10 concentrations in public places ranged from 0.102 ± 0.010 mg m-3 to 1.47 ± 0.15 mg m-3, and PM2.5 ranged from 0.095 ± 0.010 mg m-3 to 0.99 ± 0.10 mg m-3. Air quality index (AQI) values based on these concentrations indicate that these levels of PM range from unhealthy to hazardous in most cases. PM concentrations tend to decrease after remaining relatively constant with increasing distance from misting systems. Chemical data reveal that chloride and magnesium ions may be used as tracers of aerosolized water from misting systems. The average chloride concentration was 71 µg m-3 in misting samples and below the detection limit for Cl- (< 8.2 µg m-3) in ambient samples. The average magnesium concentration was 11.7 µg m-3 in misting samples and 0.23 µg m-3 in ambient samples.

Humans are exposed up to thousands of per- and polyfluoroalkyl substances (PFAS) in the environment, but most of the research and action has been directed towards only two PFAS compounds. These two compounds are part of a subcategory of PFAS called perfluoroalkyl acids (PFAAs). It has been a challenge for the environmental community to mitigate risks caused by PFAAs due to their high persistence and lack of effective measures to remove them from the environment, especially in heavily impacted areas like fire-training sites. The goal of this work was to further answer some questions regarding the removal of PFAAs in the environment by looking at anion exchange resin characteristics and presence of a competing compound, natural organic matter (NOM), in the adsorption of environmentally relevant PFAS compounds including the two often monitored 8-carbon chain PFAAs. Two different resins were tested with two forms of counterions, in both groundwater and NOM impacted groundwater. Resin polymer matrix was the most important property in the adsorption of PFAAs, the two resins used A520E and A860 had similar properties except for their matrices polystyrene (PS) and polyacrylic (PA), respectively. The PS base is most effective at PFAAs adsorption, while the PA is most effective at NOM adsorption. The change in the counterion did not negatively affect the adsorption of PFAAs and is, therefore, a viable alternative for future studies that include regeneration and destruction of PFAAs. The presence of NOM also did not significantly affect the adsorption of PFAAs in the PS resin A520E, although for some PFAAs compounds it did affect adsorption for the PA resin. Ultimately, PS macroporous resins with a strong Type I or Type II base work best in PFAAs removal.

The goal of this research was to study the effect of dilution on ammonium and potassium removal from real hydrolyzed urine. The performance of two natural zeolites, clinoptilolite and chabazite, was studied and compared with the help of batch equilibrium experiments at four dilution levels: 100%, 10%, 1% and 0.1% (urine volume/total solution volume). Further, the sorption behavior of other exchangeable ions (sodium, calcium and magnesium) in clinoptilolite and chabazite was studied to improve the understanding of ion exchange stoichiometry. Ammonium and potassium removal were highest at undiluted level in samples treated with clinoptilolite. This is a key finding as it illustrates the benefit of urine source separation. Chabazite treated samples showed highest ammonium and potassium removal at undiluted level at lower doses. At higher doses, potassium removal was similar in undiluted and 10% urine solutions whereas ammonium removal was the highest in 10% urine solutions. In general, chabazite showed higher ammonium and potassium removal than clinoptilolite. The result showed that ion exchange was stoichiometric in solutions with higher urine volumes.

The occurrence of micro-and nanoplastic (MNP) debris in the environment is a research area of considerable public health concern. Various combinations of methods for extraction, isolation, and quantification of MNP have been applied but literature studies evaluating the appropriateness and efficacy of these protocols are lacking. A meta-analysis of the literature (n=134; years 2010-2017) was conducted to inventory and assess the appropriateness of methodologies employed. Some 30.6% of studies employed visual identification only, which carried a calculated misidentification error of 25.8-74.2%. An additional 6.7% of studies reported counts for particles smaller than the cutoff value of the selected collection pore size, and 9.7% of studies utilized extraction solution densities which exclude some of the polymers commonly occurring in the environments investigated. A composite value of data vulnerability of 43.3% was determined for the sample, indicating considerable weaknesses in the robustness of information available on MNP occurrence and type. Additionally, the oxidizing solutions documented in the literature frequently were deemed unsuccessful in removing interfering organic matter. Whereas nanoplastics measuring <1 µm in diameter are likely principal drivers of health risk, polymer fragments reported on in the literature are much larger, measuring 10+ µm in diameter due to lack of standardized methods. Thus, current inventories of MNP in the environmental MNP feature data quality concerns that should be addressed moving forward by using more robust and standardized techniques for sampling, processing and polymer identification to improve data quality and avoid the risk of misclassification.