The human ankle is a vital joint in the lower limb of the human body. As the point of interaction between the human neuromuscular system and the physical world, the ankle plays important role in lower extremity functions including postural balance and locomotion . Accurate characterization of ankle mechanics in lower extremity function is essential not just to advance the design and control of robots physically interacting with the human lower extremities but also in rehabilitation of humans suffering from neurodegenerative disorders.

In order to characterize the ankle mechanics and understand the underlying mechanisms that influence the neuromuscular properties of the ankle, a novel multi-axial robotic platform was developed. The robotic platform is capable of simulating various haptic environments and transiently perturbing the ankle to analyze the neuromechanics of the ankle, specifically the ankle impedance. Humans modulate ankle impedance to perform various tasks of the lower limb. The robotic platform is used to analyze the modulation of ankle impedance during postural balance and locomotion on various haptic environments. Further, various factors that influence modulation of ankle impedance were identified. Using the factors identified during environment dependent impedance modulation studies, the quantitative relationship between these factors, namely the muscle activation of major ankle muscles, the weight loading on ankle and the torque generation at the ankle was analyzed during postural balance and locomotion. A universal neuromuscular model of the ankle that quantitatively relates ankle stiffness, the major component of ankle impedance, to these factors was developed.

This neuromuscular model is then used as a basis to study the alterations caused in ankle behavior due to neurodegenerative disorders such as Multiple Sclerosis and Stroke. Pilot studies to validate the analysis of altered ankle behavior and demonstrate the effectiveness of robotic rehabilitation protocols in addressing the altered ankle behavior were performed. The pilot studies demonstrate that the altered ankle mechanics can be quantified in the affected populations and correlate with the observed adverse effects of the disability. Further, robotic rehabilitation protocols improve ankle control in affected populations as seen through functional improvements in postural balance and locomotion, validating the neuromuscular approach for rehabilitation.

As the world population continues to age, the demand for treatment and rehabilitation of long-term age-related ailments will rise. Healthcare technology must keep up with this demand, and existing solutions must become more readily available to the populace. Conditions such as impairment due to stroke currently take months or years of physical therapy to overcome, but rehabilitative exoskeletons can be used to greatly extend a physical therapist’s capabilities.

In this thesis, a rehabilitative knee exoskeleton was designed which is significantly lighter, more portable and less costly to manufacture than existing designs. It accomplishes this performance by making use of high-powered and weight-optimized brushless DC (BLDC) electric motors designed for drones, open-source hardware and software solutions for robotic motion control, and rapid prototyping technologies such as 3D printing and laser cutting.

The exoskeleton is made from a series of laser cut aluminum plates spaced apart with off-the-shelf standoffs. A drone motor with a torque of 1.32 Nm powers an 18.5:1 reduction two-stage belt drive, giving a maximum torque of 24.4 Nm at the output. The bearings for the belt drive are installed into 3D printed bearing mounts, which act as a snug intermediary between the bearing and the aluminum plate. The system is powered off a 24 volt, 1,500 MAh lithium battery, which can provide power for around an hour of walking activity.

The exoskeleton is controlled with an ODrive motor controller connected to a Raspberry Pi. Hip angle data is provided by an IMU, and the knee angle is provided by an encoder on the output shaft. A compact Rotary Series Elastic Actuator (cRSEA) device is mounted on the output shaft as well, to accurately measure the output torque going to the wearer. A Proportional-Derivative (PD) controller with feedforward relates the input current with the output torque. The device was tested on a treadmill and found to have an average backdrive torque of 0.39 Nm, significantly lower than the current state of the art. A gravity compensation controller and impedance controller were implemented to assist during swing and stance phases respectively. The results were compared to the muscular exertion of the knee measured via Electromyography (EMG).

Current exosuit technologies utilizing soft inflatable actuators for gait assistance have drawbacks of having slow dynamics and limited portability. The first part of this thesis focuses on addressing the aforementioned issues by using inflatable actuator composites (IAC) and a portable pneumatic source. Design, fabrication and finite element modeling of the IAC are presented. Volume optimization of the IAC is done by varying its internal volume using finite element methods. A portable air source for use in pneumatically actuated wearable devices is also presented. Evaluation of the system is carried out by analyzing its maximum pressure and flow output. Electro-pneumatic setup, design and fabrication of the developed air source are also shown. To provide assistance to the user using the exosuit in appropriate gait phases, a gait detection system is needed. In the second part of this thesis, a gait sensing system utilizing soft fabric based inflatable sensors embedded in a silicone based shoe insole is developed. Design, fabrication and mechanical characterization of the soft gait detection sensors are given. In addition, integration of the sensors, each capable of measuring loads of 700N in a silicone based shoe insole is also shown along with its possible application in detection of various gait phases. Finally, a possible integration of the actuators, air source and gait detection shoes in making of a portable soft exosuit for knee assistance is given.

It has been repeatedly shown that females have lower stability and increased risk of ankle injury when compared to males participating in similar sports activities (e.g., basketball and soccer), yet sex differences in neuromuscular control of the ankle, including the modulation of ankle stiffness, and their contribution to stability remain unknown. To identify sex differences in human ankle stiffness, this study quantified 2- dimensional (2D) ankle stiffness in 20 young, healthy men and 20 young, healthy women during upright standing over a range of tasks, specifically, ankle muscle co-contraction tasks (4 levels up to 20% maximum voluntary co-contraction of ankle muscles), weight-bearing tasks (4 levels up to 90% of body weight), and ankle torque generation tasks accomplished by maintaining offset center-of-pressure (5 levels up to +6 cm to the center-of-pressure during quiet standing). A dual-axial robotic platform, capable of perturbing the ankle in both the sagittal and frontal planes and measuring the corresponding ankle torques, was used to reliably quantify the 2D ankle stiffness during upright standing. In all task conditions and in both planes of ankle motion, ankle stiffness in males was consistently greater than that in females. Among all 26 experimental conditions, all but 2 conditions in the frontal plane showed statistically significant sex differences. Further analysis on the normalized ankle stiffness scaled by weight times height suggests that while sex differences in ankle stiffness in the sagittal plane could be explained by sex differences in anthropometric factors as well as neuromuscular factors, the differences in the frontal plane could be mostly explained by anthropometric factors. This study also demonstrates that the sex differences in the sagittal plane were significantly higher as compared to those in the frontal plane. The results indicate that females have lower ankle stiffness during upright standing thereby providing the neuromuscular basis for further investigations on the correlation of ankle stiffness and the higher risk of ankle injury in females.

Presented in this thesis are two projects that fall under the umbrella of magnetically actuated electronics and robotics for medical applications. First, magnetically actuated tunable soft electronics are discussed in Chapter 2. Wearable and implantable soft electronics are clinically available and commonplace. However, these devices can be taken a step further to improve the lives of their users by adding remote tunability. The four electric units tested were planar inductors, axial inductors, capacitors and resistors. The devices were made of polydimethylsiloxane (PDMS) for flexibility with copper components for conductivity. The units were tuned using magnets and mobile components comprised of iron filings and ferrofluid. The characteristic properties examined for each unit are as follows: inductance and quality factor (Q-factor) for inductors, capacitance and Q-factor for capacitors, and impedance for resistors. There were two groups of tuning tests: quantity effect and position effect of the mobile component. The position of the mobile component had a larger effect on each unit, with 20-23% change in inductance for inductors (from 3.31 µH for planar and 0.44 µH for axial), 12.7% from 2.854 pF for capacitors and 185.3% from 0.353 kΩ for resistors.

Chapter 3 discusses a magnetic needle tracking device with operative assistance from a six degree-of-freedom robotic arm. Traditional needle steering faces many obstacles such as torsional effects, buckling, and small radii of curvature. To improve upon the concept, this project uses permanent magnets in parallel with a tracking system to steer and determine the position and orientation of the needle in real time. The magnet configuration is located at the end effector of the robotic arm. The trajectory of the end effector depends on the needle’s path, and vice versa. The distance the needle travels inside the workspace is tracked by a direct current (DC) motor, to which the needle is tethered. Combining this length with the pose of the end effector, the position and orientation of the needle can be calculated. Simulation of this tracking device has shown the functionality of the system. Testing has been done to confirm that a single magnet pulls the needle through the phantom tissue.

Unmanned subsurface investigation technologies for the Moon are of special significance for future exploration when considering the renewed interest of the international community for this interplanetary destination. In precision agriculture, farmers demand quasi-real-time sensors and instruments with remote crop and soil detection properties to meet sustainability goals and achieve healthier and higher crop yields. Hence, there is the need for a robot that will be able to travel through the soil and conduct sampling or in-situ analysis of the subsurface materials on earth and in space. This thesis presents the design, fabrication, and characterization of a robot that can travel through the soil. The robot consists of a helical screw design coupled with a fin that acts as an anchor. The fin design is an integral part of the robot, allowing it to travel up and down the medium unaided. Experiments were performed to characterize different designs. It was concluded that the most energy-efficient speed from traveling down the medium is 20 rpm, while 60 rpm was the efficient speed for traveling up the medium. This research provides vital insight into developing subsurface robots enabling us to unearth the valuable knowledge that subsurface environment holds to help the agricultural, construction, and exploration communities.

This thesis will cover the basics of 2-dimensional motion of a parafoil system to determine and
design an altitude controller that will result in the parafoil starting at a location and landing within the
accepted bounds of a target location. It will go over the equations of motion, picking out the key
formulas that map out how a parafoil moves, and determine the key inputs in order to get the desired
outcome of a controlled trajectory. The physics found in the equations of motion will be turned into
state space representations that organize it into differential equations that coding software can make
use of to make trajectory calculations. MATLAB is the software used throughout the paper, and all code
used in the thesis paper will be written out for others to check and modify to their desires. Important
aspects of parafoil gliding motion will be discussed and tested with variables such as the natural glide
angle and velocity and the utilization of checkpoints in trajectory controller design. Lastly, the region of
attraction for the controller designed in this thesis paper will be discussed and plotted in order to show
the relationship between the four input variables, x position, y position, velocity, and theta.
The controller utilized in this thesis paper was able to plot a successful flight trajectory from
10m in the air to a target location 50m away. This plot is found in figure 18. The parafoil undershot the
target location by about 9 centimeters (0.18% error). This is an acceptable amount of error and shows
that the controller was a success in controlling the system to reach its target destination. When
compared to the uncontrolled flight in figure 17, the target will only be reached when a controller is
applied to the system.

Advancements in the field of design and control of lower extremity robotics requires a comprehensive understanding of the underlying mechanics of the human ankle. The ankle joint acts as an essential interface between the neuromuscular system of the body and the physical world, especially during locomotion. This paper investigates how the modulation of ankle stiffness is altered throughout the stance phase of the gait cycle depending on the environment the ankle is interacting with. Ten young healthy subjects with no neurological impairments or history of ankle injury were tested by walking over a robotic platform which collected torque and position data. The platform performed a perturbation on the ankle at 20%, 40%, and 60% of their stance phase in order to estimate ankle stiffness and evaluate if the environment plays a role on its modulation. The platform provided either a rigid environment or a compliant environment in which it was compliant and deflected according to the torque applied to the platform. Subjects adapted in different ways to achieve balance in the different environments. When comparing the environments, subjects modulated their stiffness to either increase, decrease, or remain the same. Notably, stiffness as well as the subjects’ center of pressure was found to increase with time as they transitioned from late loading to terminal stance (heel strike to toe-off) regardless of environmental conditions. This allowed for a model of ankle stiffness to be developed as a function of center of pressure, independent of whether a subject is walking on the rigid or compliant environment. The modulation of stiffness parameters characterized in this study can be used in the design and control of lower extremity robotics which focus on accurate biomimicry of the healthy human ankle. The stiffness characteristics can also be used to help identify particular ankle impairments and to design proper treatment for individuals such as those who have suffered from a stroke or MS. Changing environments is where a majority of tripping incidents occur, which can lead to significant injuries. For this reason, studying healthy ankle behavior in a variety of environments is of particular interest.

This paper presents the design of a pneumatic actuator for a soft ankle-foot orthosis, called the Multi-material Actuator for Variable Stiffness (MAVS). This pneumatic actuator consists of an inflatable soft fabric actuator fixed between two layers of rigid retainer pieces. The MAVS is designed to be integrated with a soft robotic ankle-foot orthosis (SR-AFO) exosuit to aid in supporting the human ankle in the inversion/eversion directions. This design aims to assist individuals affected with chronic ankle instability (CAI) or other impairments to the ankle joint. The MAVS design is made from compliant fabric materials, layered and constrained by thin rigid retainers to prevent volume increase during actuation. The design was optimized to provide the greatest stiffness and least deflection for a beam positioned as a cantilever with a point load. The design of the MAVS took into account passive stiffness of the actuator when combining rigid and compliant materials so that stiffness is maximized when inflated and minimal when passive. An analytic model of the MAVS was created to evaluate the effects in stiffness observed by varying the ratio in length between the rigid pieces and the soft actuator. The results from the analytic model were compared to experimentally obtained results of the MAVS. The MAVS with the greatest stiffness was observed when the gap between the rigid retainers was smallest and the rigid retainer length was smallest. The MAVS design with the highest stiffness at 100 kPa was determined, which required 26.71 ± 0.06 N to deflect the actuator 20 mm, and a resulting stiffness of 1,335.5 N/m and 9.1% margin of error from the model predictions.

Each year, the average vehicle contributes 4.6 metric tons of carbon dioxide into the atmosphere [1]. These gases contribute to around 30,000 premature deaths each year [2] and are linked to in the increase in cases of Asthma. Human health is further impacted by the increase of greenhouse gasses in the atmosphere. Rays from the sun travel to the Earth where they are absorbed. Absorbing the sun’s rays heats up the Earth which is then radiated into space. Greenhouse gasses inhibit this process much like the glass walls in a greenhouse. As a result, the temperature of the Earth steadily increases. The greenhouse effect is dangerous because it can be linked to natural disasters, rising ocean levels, and extinction of species. One of the biggest contributors to the greenhouse effect is burning fossil fuels. Powerplants, agriculture, and transportation are some of the largest contributors to the increase of atmospheric carbon dioxide. To mitigate the effects of transportation, car companies have invested into production of alternative and renewable fuels for their products. One of the sources which has gained popularity recently, is the use of electricity to power our vehicles. Tesla has spearheaded the electric car movement and is largely responsible for this beneficial shift. One issue with this approach is that a majority, around 76.3%, of Americans drive alone on their commute [13]. The market in its current state encourages inefficient transportation due to the lack of alternatives. While motorcycles may offer a more eco-friendly and economical approach to cars, many are afraid of potential hazards of using this mode of transportation. The introduction of electric bikes offers an interesting approach to improving this efficiency and safety issue. The wide availability to customers offers an alternative which pushes the traditional distance limits for commuting on a bicycle. Since the market is relatively new, several issues pose challenges to consumers. This research aims to clarify and analyze the electric bike market in order to supply a potential customer with the tools needed to acquire a high quality and reasonably price bike.