Modeling and Simulation of Ironmaking using Hydrogen on Laboratory Scale, Pilot Scale, and Industrial Scale

193367-Thumbnail Image.png
Description
The ironmaking process involves the removal of oxygen atoms from the iron oxides to produce iron. Currently, the coal/coke-based blast furnace process dominates the industry with a 71% share of global steel production, making it responsible for 25% of total

The ironmaking process involves the removal of oxygen atoms from the iron oxides to produce iron. Currently, the coal/coke-based blast furnace process dominates the industry with a 71% share of global steel production, making it responsible for 25% of total global industrial CO2 emissions. Several processes have been commercialized to reduce these CO2 emissions such as the direct reduction process which utilizes natural gas for energy and reducing agent. In the last few decades, H2 has been identified as an alternative reducing agent in place of coal and reformed natural gas for decarbonizing the ironmaking process.To commercialize the H2 direct reduction (H2DR) process, it is necessary to study this process on a laboratory, pilot, and industrial scale to identify and address the roadblocks in the path of commercialization. Based on the literature review performed in this dissertation, four knowledge gaps were identified, and hypotheses were formulated to address the same. First, a numerical model was developed for a single iron ore pellet reduction process with a dynamic porosity function, and it was validated using experiments. Second, the equation of the radius of pellet was derived as a function of the degree of reduction using experimental data to account for the shrinking and swelling. Third, a numerical model was developed for a pilot scale H2DR reactor and was validated for average metallization of the pellets at the reactor outlet and the internal temperature profile in the reduction zone. Fourth, the numerical model for the pilot scale H2DR reactor showed a gradient of metallization at the outlet boundary which was validated by experimental metallization analysis of 31 randomly selected pellet samples one by one. At the end of the dissertation, the pilot scale model of the H2DR reactor was scaled up to an industrial scale with a DRI production capacity of 2.38 million tons/year approximately. The mass balance obtained from the industrial scale model was used to perform the techno-economic analysis to determine the economic implications of shifting from a 100% natural gas operation to a 100% H2 operation on an industrial scale.
Date Created
2024
Agent

Study of Thermophysical Properties of the Slag to Predict the Slag Foaming Model: Effect of Cr2O3 Addition in EAF Slags

189370-Thumbnail Image.png
Description
The characterization of interface properties in molten slag is crucial for understanding the interface phenomenon and the reactions between slag and metal. This study focuses on examining the influence of Cr2O3, an important surface active oxide, on the wettability and

The characterization of interface properties in molten slag is crucial for understanding the interface phenomenon and the reactions between slag and metal. This study focuses on examining the influence of Cr2O3, an important surface active oxide, on the wettability and surface tension of slag. Industrial Electric Arc Furnace (EAF) slag with two different Cr2O3 contents (1 wt% and 3 wt%) was investigated using the sessile drop measurement technique at a high temperature of 1650°C. For the preparation of 3 wt% Cr2O3-doped slags, the following crucibles were used: Al2O3, Mo, and MgO. The behavior of crucibles, the dissolution process as well as its effect on the slag thermophysical properties were studied. For the evaluation of surface tension, Mo and MgO substrates were used. The contact angle was measured using the sessile drop method, and the surface tension was calculated using the Young-Laplace-based software. The interaction and wettability behavior between the slag and different substrates was studied. The effects of Cr2O3 content, in correlation with Al2O3, Mo, and MgO, as well as temperature, on the surface tension, and phase formation were analyzed using FactSage 8.2. The results indicate an increase in the formation of solid phases with Al2O3 and Mo dissolution into the slag. The composition of the MoO3 is confirmed with the XRF and EDS analysis. Furthermore, an increase in the formation of the spinel phase was observed with the addition of chromium, which is confirmed via XRD. The increase in the CaCrMo-oxide-based spinel led to a decrease in the surface tension of the slag. The surface tension of the slag pre-melted in a Mo, decreases as the Cr2O3 content increases. The effects of the amounts of Cr2O3 in correlation with Al2O3, MgO, and MoO3 on the slag foaming index were determined using the existing models in the literature.
Date Created
2023
Agent

Assessing the Impact of Increased Parameter Modeling of Combustion Turbines in a Grid with Varying Renewable Energy Penetration Using PLEXOS

189269-Thumbnail Image.png
Description
As the share of variable renewable energy generation in the power system increases, there is a growing need for flexible resources to balance the resulting variability. Although many systems are transitioning away from fossil fuels, open-cycle gas turbines are likely

As the share of variable renewable energy generation in the power system increases, there is a growing need for flexible resources to balance the resulting variability. Although many systems are transitioning away from fossil fuels, open-cycle gas turbines are likely to fill this balancing role for some time. Accordingly, accurate production cost modeling of the operational parameters of gas turbines will be increasingly crucial as these units are relied on more heavily for flexibility. This thesis explores the impact of three additional parameters—start-up profiles/costs, run-up rates, and forced outage rates—in the production cost modeling of a system as it adopts higher levels of wind and solar. Using PLEXOS simulations of the publicly available National Renewable Energy Laboratory’s 118 bus test system, the study examines how higher the increase in parameter modeling affects outcomes such as the number of start-ups and shut-downs, ramping, total generation costs for open-cycle gas turbines, and system-wide costs in three variable renewable energy penetration scenarios. The outcome of replacing certain conventional generation units with newer and more flexible combustion turbines is also examined. The results suggest the importance of detailed parameter modeling and continued research on the formulation of production cost models for flexible generation resources such as combustion turbines.
Date Created
2023
Agent

Decarbonization of Steel and Comparative Analysis With Alternative Materials

187751-Thumbnail Image.png
Description
The purpose of this study was to comprehend the global warming potential (GWP), cost variability, and competitiveness of steel with rising carbon taxes. Aluminum, glass fiber composite, and carbon fiber composite were chosen as competing materials. In order to compare

The purpose of this study was to comprehend the global warming potential (GWP), cost variability, and competitiveness of steel with rising carbon taxes. Aluminum, glass fiber composite, and carbon fiber composite were chosen as competing materials. In order to compare the aforementioned factors, the GWP of several processes to produce steel, aluminum, and fiber composites was examined. Cost analyses of various methods were also carried out to determine their viability. Energy consumption data for each of the paths under consideration were taken from the literature for the study. To get the consistent GWP for traditional and decarbonized scenarios, the required energy is multiplied with corresponding energy source (natural gas or electricity). Even after accounting for the carbon tax and the weight-reduction factor, the results show that steel still has the lowest production costs, followed by aluminum, while fiber composites remain the most costly. EAF- steel and secondary aluminum has least GWP followed by H2-DRI (Hydrogen- Direct Reduced Iron)steel and NG-DRI (Natural Gas- Direct Reduced Iron) steel with carbon capture and storage (CCS). The state of art technology for glass fiber reinforced composite also emits less carbon dioxide but the cost of production is still high. Carbon fiber reinforced composite emits most carbon dioxide and is least economical.
Date Created
2023
Agent